Foxoyo
Hey..!!
Series
Practice
MCQs
Quizzes
About
Leaderboard
Amazon Books
44
MCQs
0
Attempts
0 %
Accuracy
share
Filter by
Type here
Apply
The first goal(s) to accomplish in analyzing a complex series–parallel circuit is to
solve for all the voltage drops
equate all parallel components
equate all series components
solve for the total current and resistance
If the load in the given circuit is 120 k , what is the loaded output voltage
4.21 V
15.79 V
16 V
19.67 V
A Thevenin equivalent circuit contains _____
many voltage sources
resistors in a series-parallel configuration
a voltage source in series with a resistance
a current source in series with a resistance
In the given circuit, the voltage at point A equals ______
+9 V
+10 V
+1 V
–10 V
The loading effect of a voltmeter can be ignored if ____
the measured voltage is very high
the measured voltage is very low
the meter's resistance is at least 10 times less than the resistance across which it is connected
If a Wheatstone bridge is balanced, a voltmeter in the center of the bridge will read
the same as the source voltage
twice the source voltage
zero volts
half the source voltage
What is the voltage to the load
15.4 V
13.4 V
12.4 V
11.4 V
What determines if resistor connections are in series, parallel, or series–parallel
current flow
resistance
the power source
the voltage source
In the given circuit, the total resistance (RT) between points A and B equals _____
1,010
100
10
900
A Wheatstone bridge can be used to determine an unknown
Voltage
Power
Current
resistance
With 21 V applied, if R1 = 5 ohms, R2 = 35 ohms, and R3 = 14 ohms, what is the current of R2 if R1 is series connected with parallel circuit R2 and R3
400 mA
800 mA
600 mA
200 mA
What theorem replaces a complex network with an equivalent circuit containing a source voltage and a series resistance
Multinetwork
Thevenin
superposition
Norton
If a Wheatstone bridge is balanced, its output voltage is ____
equal to 0 V
dependent on the unknown resistor value
the same as its input voltage
very high
___ is often used to analyze multiple-source circuits
Kirchhoff's Law
Ohm's law
Thevenin's theorem
superposition
When placed into a circuit, how are electronic components usually connected
positive terminal to positive terminal
as a combination of series and parallel
in parallel
in series
When a load is connected to a voltage divider, the total resistance of the circuit will
double
Remain the same
Increase
Decrease
When a load is connected to a voltage divider, the total resistance of the circuit will ________
double
Remain the same
Decrease
Increase
In the given circuit, the voltage dropped across R1 equals _____
1 V
9 V
19 V
10 V
In a series–parallel circuit, individual component power dissipations are calculated using
total current squared multiplied by the resistor values
a percent of the total power depending on resistor ratios
a percent of the voltage division ratio squared
individual component parameters
What is the power dissipated by R2, R4, and R6
P2 = 417 mW, P4 = 193 mW, P6 = 166 mW
P2 = 407 mW, P4 = 183 mW, P6 = 156 mW
P2 = 387 mW, P4 = 163 mW, P6 = 136 mW
P2 = 397 mW, P4 = 173 mW, P6 = 146 mW
1
2
3
Next
take a quick Quiz
Practice mcqs on Series
Let's start
pick difficulty level
all
1
2
3
4
5
44
Mcqs
0
attempts
1
followers
Related Topics
Number series
Series Completion
Letter Series
Symbol Series
Series Circuits
Series
Odd Man Out and Series
Time Series Patterns
Sequences and Series
Series RLC Circuit
Suggested Books
Javascript is disabled
we serve best when javscript is enabled
Enable